Easy to install. Affordable. Reliable.
G4X PlugIn ECUs offer the latest in engine management technology, designed to easily maximize the potential from your car.
This ECU fits inside the factory OEM enclosure. Installation of the processing unit is a breeze, with no alteration of the factory wiring loom required for the models listed below.
Designed for the Honda S2000 AP1.
Please check your connector matches the header in the listed photo before purchasing.
This ECU works for manual transmissions only.
This ECU doesn't support factory E-Throttle Models
Most factory features are supported.
Check the features tab for I/O input & output expansion options
Note: This Plug-in features a new 4 pin powered CAN connector and cannot use the old CANPCB cable for CAN connection. Use the CANJST4 (Code 101-0198) cable for connecting CAN devices. This new 4 pin port and cable provide not only the CAN connection, but also a protected 12V power supply and ground for powering the CAN devices. The power supply is protected by a self-resetting fuse rated at 3A continuous.
Suitable applications for 233-4000 automotive computer unit:
Honda S2000 AP1 1999-2004
Honda S2000 AP2 2005 (Non E-throttle)
G4X PlugIn Key Features (where applicable):
Up to 6D fuel and ignition mapping
Precision closed loop cam control (four cam, independent control)
Sequential fuel delivery
Digital triggering, all OEM patterns
OEM idle hardware supported
5D boost control with three switchable tables
Motorsport features - antilag, launch, flat shift
Continuous barometric correction (on board)
CAN port
QuickTune - automated fuel tuning
Individual cylinder correction
USB tuning cable included
Stats recording into on-board memory
Gear compensations for spark, boost and fuel
Real time selectable dual fuel, ignition and boost maps
Sync and crank sensors can be a combination of Hall effect, variable reluctance or optical
Boost control referenced to gear, speed or throttle position
512 mega bytes data logging memory within data processing unit
Staged injection
Knock with "windowing"
I/O Expansion Options:
The following expansion connector inputs/outputs are provided:
E-Throttle Connector
E-Throttle 1 - Ground (Signal)
E-Throttle 2 - +5V Out
E-Throttle 3 - An Volt 10
E-Throttle 4 - An Volt 9
E-Throttle 5 - An Volt 8
E-Throttle 6 - An Volt 7
E-Throttle 7 - Aux 10
E-Throttle 8 - Aux 9
Expansion Connector 1
Expansion 1 - Ground (Signal)
Expansion 2 - Aux 11
Expansion 3 - Aux 6
Expansion 4 - DI 11
Expansion 5 - DI 10
Expansion 6 - DI 9
Expansion 7 - DI 2
Expansion 8 - DI 1
Expansion Connector 2
Expansion 9 - Ground (Signal)
Expansion 10 - Aux 16
Expansion 11 - Not Connected
Expansion 12 - Not Connected
Expansion 13 - Not Connected
Expansion 14 - Not Connected
Expansion 15 - An Volt 12
Expansion 16 - An Volt 6
Link Engine Management Ltd – Limited Lifetime Warranty
This Limited Lifetime Warranty applies to all Engine Control Units (ECUs), Power Distribution Modules (PDMs), DI-Drivers, and CAN-Lambda modules (“Products”) manufactured by Link Engine Management Ltd.
WARRANTY COVERAGE
Link Engine Management Ltd warrants that its Products are free from defects in materials and workmanship under normal use and installation, for the lifetime of the Product, subject to the limitations outlined below. This warranty applies only to the original purchaser of the Product and is non-transferable.
If a defect arises and a valid claim is received, Link Engine Management Ltd will, at its sole discretion:
repair the defective Product, or
replace it with a new or refurbished Product of comparable function.
If a Product is found to be defective, it must be returned to the original place of purchase along with proof of purchase. Any repaired or replaced Product is covered only for the remainder of the original warranty period.
WARRANTY EXCLUSIONS
This warranty does not cover:
Products that have been damaged or impaired due to incorrect installation, misuse, neglect, accident, or external causes,
Normal wear and tear or cosmetic damage,
Products that have been modified or used with incompatible software or components,
Are installed in highway-registered vehicles (Products are intended for off-road use only).
CONSUMER RIGHTS
This warranty provides specific legal rights and may be supplemented by local consumer protection laws in your country. Where applicable, you may have additional rights under national legislation, including but not limited to:
The Consumer Guarantees Act (New Zealand),
The Australian Consumer Law,
The Magnuson-Moss Warranty Act (USA),
The EU Consumer Rights Directive.
Nothing in this warranty limits or excludes any rights you may have under such laws.
LIMITATIONS
Link Engine Management Ltd is not liable for any:
Indirect or consequential losses (such as vehicle damage, loss of income, or labour costs),
Damages arising from the use of the Product outside its intended purpose,
Failures caused by third-party software or incorrect setup of user-configurable features.
SOFTWARE LICENCE
The Product includes a user-configurable software programme, which must be installed using the latest version available from the Link Engine Management website.
The warranty is voided if:
The incorrect or outdated software version is used, or
The user attempts modifications or setups that aren’t supported.
The software included in the Product is licensed, not sold. It may only be used in accordance with Link’s license terms. Link Engine Management Ltd grants the user a non-exclusive license to use the software:
Only in the country where it was originally acquired,
On a single device at a time,
In accordance with the applicable End User Licence Agreement (EULA).
If the license is terminated by you or by Link (e.g. for breach of terms), the software must be permanently deleted.
